Ren Molnar Archive - Home Focus



Home \| Contact Us \| Job Opportunities \| Client Login

It's fast, easy
& free!
click here

I forgot my password

Ren Molnar Bio

Ren Molnar Archive

Homefocus Archive

Expert Q Ren Molnar Q&A Archive

Top > Tools & Equipment > Tool & Equipment

Question:

I am thinking of buying a router to assist me in building some cabinetry and doing some finishing touches on some projects at home and the cottage.I want a plunge router, but should I get a half inch or quarter inch chuck router.What are some things I should consider re power etc.

Answer:

I have one that will accept a half inch or quarter inch shank and as far as I'm concerned, about the only real things I look for are: 25K RPM, electronically controlled cut-out switch and lighting.

Answered By: Ren Molnar

More Questions & Answers ...

1.	Is there a simple way to eliminate a fairly deep cigarette burn in a soft wood table top (maybe pine) without ...
2.	The furnace was replaced and moved. Where the old furnace was is left a concrete pad approx. 5X3 ft. and 1 ft. ...
3.	The carport lean-to is completely open on three sides sharing one wall of the garage. It consists of only a ro ...
4.	I wish to refinish our wooden fireplace mantle. It is presently a stained finish, but one side faces a stairca ...
5.	Our home is 17 years old and I am starting to notice that a couple of our doors are starting to separate(panel ...
6.	I am having a dispute for the last 20 years with a neighbor who is now at the point of shouting out insults wh ...
7.	I recently bought a used 10 gauge 21 angle air framing nailer. The nails are in strips not a coil. I used it o ...
8.	I want to know how to read a tape measure ...
9.	What is the best tool to use to cut panneling. The panneling is very thin and since this will be the finishing ...
10.	How can I lay out a 65 degree angle on a framing square? ...
11.	I have an old carpetners square and on the short arm are the numbers (hand stamped) 2545-2970-3395-3819-4243 e ...
12.	What is the difference between a pancake style compressor and a double tank style compressor. ...
13.	What is the best/easiest way to strip plastic laminate from a coffee table - preferably without chemicals. ...
14.	What is a double pinned marking gauge? ...
15.	I am thinking of buying a router to assist me in building some cabinetry and doing some finishing touches on s ...
16.	how do I use it? ...
17.	I need your help as I want to surprise my husband with a cordless drill for his birthday in September. He only ...
18.	How do you find the center of a circle using a carpenter's square? ...
19.	Do you know the best way to drill an extra tap hole in a stainless steel kitchen sink? Would a bi-metal hole s ...
20.	thanks for answering my question. also, one more thing, is it important to use a notched trowel then a regular ...
21.	I'm actually asking this on behalf of my dad. As a young carpenter many years ago, he once saw an old-tim ...
22.	We have a 3 storey 100 yr+ house. The floor joists on the first floor are 2"X 8' 2' on center with a 1 ...
23.	My 30 year old detached garage has developed a 4 inch sag in the roof line. This is a 2 car garage about 20x24 ...
24.	My front hand rail is made of hard wood (I'm not a connoisseur of wood) and the finish is looking old, warn d ...
25.	Can I paint over cupboard doors in the kitchen that were painted and then varathaned, or do I have to sand the ...
26.	I've heard you say many times how easy it is to remove water stains from wooden tables. Now it's happened to ...
27.	Recently our daughter and son-in-law purchased an older house (about 70 years old), and found all the walls we ...

Home Plans